03bf454c

6.17. An accelerator rope - removal, installation and adjustment

Models without system a cruise control
Cordia, Tredia, Colt, Lancer, Mirage (except MPI) and Precis (except MPI)
1. On carburetor engines remove the air filter.

16.2 Turn off an adjusting nut (it is specified by an arrow) and disconnect an accelerator rope from an arm


2. Turn off an adjusting nut (16.2) and remove a rope from an arm.

16:3á Remove the finishing panel under the dashboard and disconnect a rope in the point specified by an arrow.


16:3í Disconnect a rope from a fire-prevention partition turning off two fixing bolts and remove a rope guide from a partition.


3. Disconnect a rope from the carburetor and the accelerator pedal. Remove a rope from a back wall of a motive compartment (16.3a and 16.3b).
4. Remove a rope from the car.
5. Installation is carried out upside-down removals.
Galant, Colt, Lancer, Mirage and Precis (MPI) Removal and installation

16.6 Elements of a rope of an accelerator of the Galant, Colt, Lancer, Mirage and Precis models (without cruise control)

1 Rope
2 Adjusting bolt
3 Rope
4 Plug
5 Arm
6  I will corrode connections of the switch of an accelerator (models with the automatic transmission]
7 Returnable spring
8 Accelerator pedal
9 Check


6. Get a rope from arms, disconnect it from the accelerator pedal and the case of a throttle and remove from the car (16.3a, 16.3b and 16.6).
7. Installation is carried out upside-down removals.
Adjustment
8. Warm up the engine and check idling speed. Adjust it if it is necessary. Kill the engine.
9. Press a pedal of an accelerator and check that the lever of a butterfly valve moved smoothly, and completely opened the gate.
10 Include ignition for 15 seconds
11   Turn off two bolts fixing a rope near the throttle case
12 Pull a rope and tighten two bolts Check that the lever of a butterfly valve concerned a rod of a vacuum diaphragm
Models with system a cruise control
Cordia and Tredia
Accelerator pedal rope

16:13 Elements of fastening of a rope of an accelerator on the Cordia and Tredia models with system a cruise control. Adjusting nuts are specified by shooters


13 Turn off adjusting nuts and disconnect a rope from the lever of a butterfly valve and an arm (16.13)
14 Remove a rope
15 Installation is carried out upside-down removals
Rope of the executive mechanism
16 Disconnect a rope from the lever of a butterfly valve and the executive mechanism and remove it from the Installation car it is carried out upside-down removals
17  After installation, eliminate sagging of a rope, having tightened adjusting nuts when the engine works in the idling mode
Galant
Removal and installation
18 Remove a casing of the executive mechanism

16:19 Elements of fastening of a rope of an accelerator on the Galant model with system a cruise control

1 Rope of an accelerator And
2 Executive  mechanism  of system cruise control
3. Accelerator pedal
4. Switch
5. A connecting link In
8. Connecting link And
7. Lever of a butterfly valve
8 Adjusting bolts
9. Limiter
10. An accelerator rope In
11 Adjusting nut And
12. Lock-nut


19 Turn off an adjusting nut and remove a rope from an arm (16.19)
20 Disconnect a rope from a connecting link Disconnect a rope from a pedal and the case of a throttle and remove it from the car (16.3a)
21 Installation is carried out upside-down removals
Adjustment
22 Warm up the engine and check the speed of idling Adjust it if it is necessary Kill the engine
23 Press a pedal of an accelerator and check that the lever of a butterfly valve moved smoothly, and completely opened the gate
24 Turn off  adjusting  nuts  of a rope Include ignition for 15 seconds
25 When a connecting link (And (concerns an emphasis (16.19), tightening up an adjusting nut (And (adjust a rope tension so that a link (And (began to depart from an emphasis, then turn off a nut (And (on two turns
26. Having tightened up an adjusting nut (V), pull a rope so that the lever on a connecting link (V) concerned the lever on a link (And).
27. Turn off two fixing bolts of a rope near the case of a throttle and pull a rope Twirl lock-nuts of an intermediate link and two bolts fixing a rope near the throttle case.
Colt, Lancer, Mirage (MPI)
Removal and installation of a rope of a pedal of an accelerator

16:28 Elements of fastening of a rope of an accelerator on the models Colt, Lancer, Mirage MPI

1 Rope of an accelerator And
2 Adjusting bolt
3 Limiter
4 Connecting link And


28. Get a rope from fixing arms and disconnect it from a connecting link and a pedal of an accelerator. Get a rope through a back wall of a motive compartment and remove it from the car. Installation is carried out   upside-down removals (16.28,16.3a and 16.3b).
Removal and installation of a rope of the lever of a butterfly valve
29. Get a rope from fixing arms, disconnect it from a connecting link and the lever of a butterfly valve and remove a rope from the car. Installation is carried out upside-down removals
Adjustment
30. Remove the air filter.

16:31 For adjustment of a rope of a butterfly valve tighten up adjusting bolts
1. Adjusting bolts
2. Plate


31. Having tightened up adjusting bolts, adjust a tension of a rope of the lever of a butterfly valve that it had a small free wheeling (16.31).
32. Check that the lever concerned the switch of system of idling.
33. Check that the connecting link concerned an emphasis (16.28), then turn off an adjusting bolt of a rope of a pedal of an accelerator and pull a rope
34. Check that the butterfly valve opened completely and closed when pressing an accelerator pedal.